Harley Davidson Pan America Forum banner
21 - 40 of 49 Posts
Only one CANsmart can be plugged into the bike is my opinion. I would suggest using their chat function on their website, it works. They have an additional wiring kit for 2 sets of T3s, you may need that if not already ordered. I would also suggest reading their webpage here and watching their videos.

Chat em up!
I'm sticking around to hear @Jesse Davis results. Love the motohorn and would like to keep it if you figure out how to wire up all the denali lights OR just buy the denali sound bomb too.
 
I'm sticking around to hear @Jesse Davis results. Love the motohorn and would like to keep it if you figure out how to wire up all the denali lights OR just buy the denali sound bomb too.
Hopefully get everything installed on Sun to include the H-D Hi-flow air filter (had been waiting for it to come in) since I have to take the tank off anyway. Motohorns, CANsmart and a B6 rear light set to strobe.
 
  • Helpful
Reactions: 71Romeo
  • Like
Reactions: 71Romeo
If you want to save $110 and get the same LED lights Denali sells for $29 check out the Clearwater LED thread. Essentially it says this:

I sourced apparently the same LEDs that Denali sells for $139 for $29.99. Now Denali does give you a connector that makes it plug and play and all that for only $120 more. Seriously, I wasn't sure that it would work without tossing DTC codes, but it does work fine. Use Posi connectors to tape the right turn signal and left turn signal wires under seat. i add the led brake light also, so tape the brake light line too. i tap a common ground already on the frame for the three negative wires. Shrink wrapped everything and zip ties. Two tone flashing turn signals and rear brake light that will pulse 3 seconds before remaining solid on - Bright. PERFECT! This the Horsepoor approach because I don't want to choose between fuel for bike or grain for the horses. The horses might not be too happy.

They are even called B6 LEDs for $29.99 Come on Denali, you could least change the name to something like D6 LEDs.

Motorcycle B6 Dual License Plate Auxiliary LED Taillight Burst Flash Brake light Daytime Running lights DRL Red or Yellow (Amber) or White

B6 LEDs

We are here to save each other money and get cool stuff. I ordered a lot of stuff from this site, all good except the passenger grab rails but they warned me not to use with HD rear luggage rack and HD saddle bag kit / bags. So that is on me, gifted rails to a buddy.
 
If you want to save $110 and get the same LED lights Denali sells for $29 check out the Clearwater LED thread. Essentially it says this:

I sourced apparently the same LEDs that Denali sells for $139 for $29.99. Now Denali does give you a connector that makes it plug and play and all that for only $120 more. Seriously, I wasn't sure that it would work without tossing DTC codes, but it does work fine. Use Posi connectors to tape the right turn signal and left turn signal wires under seat. i add the led brake light also, so tape the brake light line too. i tap a common ground already on the frame for the three negative wires. Shrink wrapped everything and zip ties. Two tone flashing turn signals and rear brake light that will pulse 3 seconds before remaining solid on - Bright. PERFECT! This the Horsepoor approach because I don't want to choose between fuel for bike or grain for the horses. The horses might not be too happy.

They are even called B6 LEDs for $29.99 Come on Denali, you could least change the name to something like D6 LEDs.

Motorcycle B6 Dual License Plate Auxiliary LED Taillight Burst Flash Brake light Daytime Running lights DRL Red or Yellow (Amber) or White

B6 LEDs

We are here to save each other money and get cool stuff. I ordered a lot of stuff from this site, all good except the passenger grab rails but they warned me not to use with HD rear luggage rack and HD saddle bag kit / bags. So that is on me, gifted rails to a buddy.
Pretty sure Pazoma copied Denali, they even have some of Denali Electronic's photos on their website lol. I went with the generic Denali B6 because it plugs directly into their CANsmart device, didn't need the PAS special plugin kit to tap the factory wiring. I have the Pazoma add-on crash bars (attached to the stock bars) they give me a great place to put my feet. They also took over a month to ship so wasn't so pleased with that.
 
  • Like
Reactions: Burnin Padrons
Pretty sure Pazoma copied Denali, they even have some of Denali Electronic's photos on their website lol. I went with the generic Denali B6 because it plugs directly into their CANsmart device, didn't need the PAS special plugin kit to tap the factory wiring. I have the Pazoma add-on crash bars (attached to the stock bars) they give me a great place to put my feet. They also took over a month to ship so wasn't so pleased with that.
Now that I think about it, China wont copy something from a reputable manufacture and sell it for less? Nope, couldn't happen - not. I think you are correct.
 
Now that I think about it, China wont copy something from a reputable manufacture and sell it for less? Nope, couldn't happen - not. I think you are correct.
I was replying more for this comment you made: "Come on Denali, you could least change the name to something like D6 LEDs." If Denali was first, why should they change their names? (^;
 
I just ordered a set of T3 turn signals for the front. They are white LED until you activate the turn signal then they flash orange. There's been a set of Clearwater Darlas on the forks since last year. We used to offer those as a factory option when I worked at Motus. The Darlas cost a little more but they kick ass. I run them with the yellow lens covers, it really gets peoples attention in front of me. My wife rides with me a lot so anything I can do to make the Pan Am more visible makes me feel better.
 
I added the Denali Electronics B6 Dual brake light/running lights kit. What a difference they make. Included are all the wiring with connectors and the brackets to attach to the license plate/plate holder. The harness all connect, to include the original brake light. No cutting of wires necessary. I tried to upload a short video of the brake light(s) brightness when pressed, but could not get it to upload. View attachment 2503
This is a on my to do list for the winter. The group I ride with hates the minimal break lights on the stock bike. Thanks for the info. Love the idea of plug and play.
 
Discussion starter · #34 ·
This is a on my to do list for the winter. The group I ride with hates the minimal break lights on the stock bike. Thanks for the info. Love the idea of plug and play.
MDMoto, the kit is hard to come by, but if you order now, you should get it before the winter. I'd also look at eBay, Amazon. You might get lucky and find kit sooner.
Ride on...... brother......
 
Its shown halfway through this video:

the harness is labeled so it should be pretty self explanitory. Still, annoying that they can't provide vehicle specific instructions.

Hello there, yes I came across this video, but this is only showing the t3 or the license plate which is plug n play.They however sell the t3 turn signals which are not plug n play. I was wondering if someone here is running these? I saw one video on youtube of someone with these very same lights on their PAN AM but no wiring guide was provided either.
Thank you for your reply.
 
Discussion starter · #38 ·
Hello there, yes I came across this video, but this is only showing the t3 or the license plate which is plug n play.They however sell the t3 turn signals which are not plug n play. I was wondering if someone here is running these? I saw one video on youtube of someone with these very same lights on their PAN AM but no wiring guide was provided either.
Thank you for your reply.
Try giving Denali a call. Speak to one of their techs. They seem to be very helpful, from other threads I've read here. Hopefully they can assist with your installation. Those T3-M8 front fender turn signals look really nice an a Pan Am. Good luck, and post pics of your Pan Am, after the install.
 
Try giving Denali a call. Speak to one of their techs. They seem to be very helpful, from other threads I've read here. Hopefully they can assist with your installation. Those T3-M8 front fender turn signals look really nice an a Pan Am. Good luck, and post pics of your Pan Am, after the install.
Hello I managed to figure it out after all. I used Posi-tap to tap into the harness from Denali since the T3 turn signal does not have a female socket to connect to the harness.
Here’s vid for demo of it all hooked up. T3 demo video
 
21 - 40 of 49 Posts