[Cold]

GIVI luggage, has two rack systems for the PAS, monokey and cam to be used with their aftermarket bags. Went with the monokey rack and a 33/46L Trekker bags. Not a bad aftermarket alternative...


A few months later update: I absolutely love the bags and the ability to remove them. The locking system seemed a bit lackluster but I am happy to say the bags lock in solid and there is no free play or wiggle room. If you plan to order these bags, order the mounts (and bags if in stock) from motostorm.it, just found them today, ordered my top mount. Total with shipping from Italy was $179, vs most american dealers who sell it at msrp of $281.

Pan America 1250 '21-22'

Pan America 1250 motorcycle accessories from GIVI. Hard cases, saddle bags, engine guards, windscreens, soft luggage and tank bags.

giviusa.com

 

[ronvansickle]

I went with the same thing, waited five months for the H-D setup with a five month slip! I was lucky, a set was FEDEXed and I had them in 24 Hours!

 

[Cold]

Got my bags in last week and got them mounted. The install was just a bit tedious (make sure you have Torx drivers for removing bolts for the mounting bracket), other than that absolutely over the moon with GIVI and their Trekker bags. Went 33 on right and 46 on left, 46 is big enough to store helmet that has a Sena 10C Pro mounted to it.

 

[MDMoto]

View attachment 668
Got my bags in last week and got them mounted. The install was just a bit tedious (make sure you have Torx drivers for removing bolts for the mounting bracket), other than that absolutely over the moon with GIVI and their Trekker bags. Went 33 on right and 46 on left, 46 is big enough to store helmet that has a Sena 10C Pro mounted to it.

How wide is the bike with the bags on? I'm looking at the same setup, I have a 48 inch gate I have to get the bike through.

 

[Cold]

How wide is the bike with the bags on? I'm looking at the same setup, I have a 48 inch gate I have to get the bike through.

Im in the middle of a ride right now but can send a pic of the dimensions and measure it once I get home tonight. It is pretty wide I will say that much

 

[Cold]

How wide is the bike with the bags on? I'm looking at the same setup, I have a 48 inch gate I have to get the bike through.

Sorry for late reply. Measured it out this morning before going to work, sits at right about 42 inches with thr 46 and 33 trekker bags. May want to see if another line of givi bags has a lower profile that or paint a center line on the ground

 

[MDMoto]

Sorry for late reply. Measured it out this morning before going to work, sits at right about 42 inches with thr 46 and 33 trekker bags. May want to see if another line of givi bags has a lower profile that or paint a center line on the ground

Hahaha. Thanks. It will cut it close but I can do some sort of marker. If I go with two 33's I think I will get an extra 3 inches but loose room for a full face helmet

 

[Cold]

Hahaha. Thanks. It will cut it close but I can do some sort of marker. If I go with two 33's I think I will get an extra 3 inches but loose room for a full face helmet

I mean the helmet storage is more of a convenience thing. Could just do a helmet lock on the side or get the top rack mount and put the 46 up there. Thats my eventual plan (just undecided on to do a 33 or 46)

IMO two 33s would get the job done but it would be non symmetrical and I notice those things, but if it doesn't bother you go for it. I just measured it from center line and you are right you get about 3 extra inches which would bring the width to 36, so you'd have appx. 6 inches clearance both sides with two 33s

 

[Matilda]

I finished my laugage thing.
Givi trekker Alaska left and right.
Trekker 58l topcase.
Now i am ready to go.

 

[Matilda]

Different use.